Marine AF 50 Red 5 Gallon
Do you need review of Marine AF 50 Red 5 Gallon. If you find rating Marine AF 50 Red 5 Gallon. Here, you’ll be able to find the top deals available in recent market only from us. Together with it, you may also be able to discover a lot more info as well as comprehensive reviews over the infamous Marine AF 50 Red 5 Gallon. I suggest you view this article..
Marine AF 50 Red 5 Gallon
MARINE AF 50 - TBT FREE ABLATIVE ANTIFOULING High performance, moderate copper load ablative antifouling. TBT free. Used for fouling control on deep-sea vessels requiring longer drydock intervals. Product description: High performance, moderate copper load ablative antifouling.TBT free. Intended use: Used for fouling control on deep-sea vessels requiring longer drydock intervals. Product Info: ColorRed , Black Finish / sheenFlat Curing agentNot applicable, one part paint Volume solids56% 2% Mix ratioOne part Typical film thickness4.0 - 5.0 mils DFT Theo coverage180 square feet per gallon @ 5 mils DFT Flash point81 degree F Dry Times 40F50F75F90F Touch dry4 hr3 hr2 hr1 hr Before launch30 hr20 hr15 hr10 hr Overcoating Time 40F50F75F90F Min / MaxMin / MaxMin / MaxMin / Max Marine AF 4515 hr / 30 days8 hr / 30 days6 hr / 30 days4 hr / 30 days Note: Must be applied over MARINE AC 70 or MARINE AC 80 when tacky. Do not allow epoxy anticorrosive to dry hard. Apply over MARINE AC 1 when dry. Regulatory Data: * VOC 372 grams /liter or 183 grams / kg * EPA 74681-2 Product does NOT contain TBT. Systems and Compatibility: Application of MARINE AF 50 over self polishing copolymers is not recommended. Surface Preparation: Surface must be clean, dry and free of all contamination. High pressure fresh water wash to remove all soluble contaminants and foreign matter. Clean any oil or grease in accordance with SSPC-SP1 Solvent Cleaning. Newbuilding: Prepare surface and apply recommended primer. Apply two or three coats of MARINE AF 50 depending on drydock interval required. Drydocking: Insure coating is intact. Pressure wash the entire bottom with 3000 psi fresh water wash when vessel enters the dock and before the surface dries. Re- move all loosely adhering paint and fouling. Damaged areas should be prepared to SSPC-SP10 Near White Blast (Sa2.5) and coat with MARINE AC 70, MARINE AC 80, or MARINE AC 1. Comply with overcoating intervals specified by primer data sheet. Application data: Application: Apply by airless spray. Application by brush or roller will require multiple coats. . Strain material with a 60 mesh screen. Apply 7.0 mils wet to yield 4.0 mils dry film thickness. Mixing: Product contains moderate copper load. Always shake or mix thoroughly with shaker or power agitator. Thinning: Does not require thinning for spray application. If thinning is necessary, thin up to a maximum of 4 oz / gal of THINNER 975. Airless Spray: Airless spray is recommended. * Tip size 18-26 thou * Output fluid pressure at spray tip 3000 psi Conventional Spray: Conventional spray is not recommended. Brush: Brush use is recommended for small areas only. Multiple coats may be required to achieve specified film thickness. Roller: Roller use is recommended for small areas only. Multiple coats may be required to achieve specified film thickness. Cleaner: THINNER 975 Cleanup: Flush all equipment with THINNER 975. Close lid thoroughly for storage. Filter material prior to use. Safety: Refer to Material Safety Data Sheet (MSDS) for this product. The MSDS will provide all necessary data on health hazards, conditions to avoid, proper storage, disposal information, hazardous ingredients and health related characteristics. Limitations: Performance of the product is dependant upon the specified film thickness being achieved. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Apply in good weather.Temperature of the surface to be coated must be at least 3degC (5degF) above the dew point. Bring paint to 75degF prior to mixing and application. Store unused paint in a closed pail.Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating. Unit size: 5 US gallons in a 5 US gallon pail. Unit Weight: 5 US gallons pail weighs 88 pounds (16.9 pounds / gallon) Shelf life: 12 months from the date of manufacture when stored in a protected location at 40-100degF Office: Blue Water Marine 1999 Elizabeth Street, North Brunswick, NJ 08902, Phone 800-628-8422, Fax 732-821-8180, www.BlueWaterMarinePaint.com Note: Data sheet information is not intended to be exhaustive. Use of this product for any purpose other than as specified without written confirmation from Blue Water does so at their own risk. Factors outside of Blue Water control may affect the performance of this product. Blue Water does not accept any liability for the performance of this product or any loss or damage caused by the use of this product. Information in this data sheet is subject to change. User is responsible for securing the most updated data sheet prior to use of this product. All product names mentioned in this data sheet are trademarked by Blue Water Marine.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น